Light Stand Accessories FAQ
Here are frequently asked questions and answers regarding light stands and accessories. You can narrow down the question you are looking for using the search box at the top of the page. If your issue is not resolved, please contact us.
List of Questions (19)
- Can I use this with monoblock or generator strobes?
- Is it okay to use outdoors?
- How to adjust the angle adjustment lever position
- How to assemble the center pole
- What are the maximum height, minimum height, and storage dimensions?
- What should I do if the center pole comes out or won't extend?
- Can I purchase the protective cap for the LS-50C-L spigot tip individually?
- The surface of the LS-50C-L carbon pipe is peeling. Is it still safe to use?
- Tell me about light stand warranty and trade-in sales.
- If I trade in an LS-50C-L, how much does a new one cost?
- Can I purchase the rubber feet for the LS-50C?
- What is the difference between the LS-5C-XL and LS-65C?
- What should I do if the LS-50C screws come loose? Are there torque specifications?
- Can I attach the RH-100C-R II reflector holder to the LS-20C?
- Is it okay to put a weight on the legs when the light stand is about to tip over?
- What should I do if the light stand pole gets stuck and doesn't move smoothly when extending?
- How do I attach the FT-01 Free Tilter to the LS-5C-XL / LS-50C-L II?
- Is it a defect if the legs of a new LS-50C-L II are stiff and hard to open?
- Can I use the LS-50C-L with an FT-01 Free Tilter or an umbrella attached?
Q. Can I use this with monoblock or generator strobes?
Applicable models: LS-50C
A. This product is designed specifically for use with clip-on strobes.
The load capacity of this product is 1.5 kg; mounting heavy equipment such as large strobes may cause it to lose its balance. Please refrain from doing so, as there is a risk of the equipment tipping over.
The load capacity of this product is 1.5 kg; mounting heavy equipment such as large strobes may cause it to lose its balance. Please refrain from doing so, as there is a risk of the equipment tipping over.
Q. Is it okay to use outdoors?
Applicable models: LS-50C
A. This product was developed with a focus on reducing the weight of equipment during location shoots. We believe it is highly effective for lightening your load during outdoor shoots, so please feel free to use it actively outdoors.
However, please note that extremely rough handling may cause damage. In conditions where even a standard light stand might tip over or be damaged—such as stepping on it with shoes, mounting equipment with poor weight balance, or using large light accessories in strong winds—please be sure to use weights or other stability measures, or refrain from use if conditions are poor.
Additionally, if dust or moisture (especially seawater) is left on the product, it may deteriorate or become damaged. After use, please wipe off any dirt with a cloth dampened with fresh water. If using detergents or grease, please ensure they are compatible with resin.
We cannot be held responsible for any damage or malfunctions to this product, our other products, third-party equipment, or any personal injury or damage to surrounding structures caused by tipping over due to unreasonable use beyond product defects; please be extremely careful of your usage environment.
However, please note that extremely rough handling may cause damage. In conditions where even a standard light stand might tip over or be damaged—such as stepping on it with shoes, mounting equipment with poor weight balance, or using large light accessories in strong winds—please be sure to use weights or other stability measures, or refrain from use if conditions are poor.
Additionally, if dust or moisture (especially seawater) is left on the product, it may deteriorate or become damaged. After use, please wipe off any dirt with a cloth dampened with fresh water. If using detergents or grease, please ensure they are compatible with resin.
We cannot be held responsible for any damage or malfunctions to this product, our other products, third-party equipment, or any personal injury or damage to surrounding structures caused by tipping over due to unreasonable use beyond product defects; please be extremely careful of your usage environment.
Q. How to adjust the angle adjustment lever position
Applicable models: LS-50C
A. When using the LS-50C, opening the legs 180 degrees to reach the ground or closing them for storage, the tip of the angle adjustment lever may hit the ground or the pole and get in the way. 
The position of the angle adjustment lever when tightened can be adjusted in 90-degree increments. Here is how to adjust it:
1. Remove the angle adjustment lever or loosen it sufficiently.
2. The base of the screw on the opposite side of the lever is square-shaped and engages with the slit in the stand leg. Remove it from the slit, rotate it 90 degrees at a time to your preferred position, and re-engage it with the slit. (It is helpful to mark the screw head in advance so you remember the original position.)
3. Reassemble and check the position of the lever. 
When disassembling, be careful not to lose any screws or washers.
The position of the angle adjustment lever when tightened can be adjusted in 90-degree increments. Here is how to adjust it:1. Remove the angle adjustment lever or loosen it sufficiently.
2. The base of the screw on the opposite side of the lever is square-shaped and engages with the slit in the stand leg. Remove it from the slit, rotate it 90 degrees at a time to your preferred position, and re-engage it with the slit. (It is helpful to mark the screw head in advance so you remember the original position.)
3. Reassemble and check the position of the lever. 
When disassembling, be careful not to lose any screws or washers.Q. How to assemble the center pole
Applicable models: LS-50C, LS-55C, LS-65C
If you have disassembled the center pole by rotating the tab, please assemble it as follows:
STEP1
Insert the resin ring inside the tab.
STEP2
After inserting the tab into the pole, attach the stopper to the pole by aligning the hole in the pole with the protrusion on the stopper.
STEP3
Insert the pole so that the rib (protrusion) inside the pole aligns with the slit in the tab.
STEP4
Once inserted to a certain point, rotate the tab to verify that the pole is fixed.
※ If you need parts, you can purchase them here. (Some parts are not sold for certain models)
Q. What are the maximum height, minimum height, and storage dimensions?
Applicable models: LS-20C
- Maximum height is approx. 109.5 cm when the stand main unit (head), extender, handle, and free tilter mini are all connected.
- Minimum height is approx. 19 cm for the head alone (from the floor to the top screw tip), and approx. 25.5 cm for the head + free tilter mini (from the floor to the free tilter mini tip).
-
Storage dimensions are:
Stand main unit... approx. 19 cm
Extender... approx. 22 cm
Handle... approx. 14.5 cm
Free tilter mini... approx. 7 cm
Q. What should I do if the center pole comes out or won't extend?
A. Remove the pole once, clean it, and reassemble it by following the steps in How to assemble the center pole. If the problem persists, we accept repairs. Please see Support & Repairs.
Q. Can I purchase the protective cap for the LS-50C-L spigot tip individually?
Applicable models: LS-50C-L
A. Please contact us regarding the availability of this as a spare part.
Q. The surface of the LS-50C-L carbon pipe is peeling. Is it still safe to use?
Applicable models: LS-50C-L
A. The surface coating or clear layer may peel off. The impact on strength depends on the condition. If the peeling spreads or if there are cracks, please discontinue use and contact us.
Q. Tell me about light stand warranty and trade-in sales.
A. Accessory products such as light stands do not come with a 1-year manufacturer warranty. We will provide a free exchange or repair only for initial defects occurring within 14 days of purchase. For details, please see About Warranty.
The trade-in program allows you to purchase new products at a 20% discount off the catalog price. Trade-ins for light stands apply to purchases of Super Light Stand products. For details, please see Trade-in Sales.
The trade-in program allows you to purchase new products at a 20% discount off the catalog price. Trade-ins for light stands apply to purchases of Super Light Stand products. For details, please see Trade-in Sales.
Q. If I trade in an LS-50C-L, how much does a new one cost?
Applicable models: LS-50C-L
A. The trade-in program allows you to purchase new products at a 20% discount off the catalog price. Please check the Trade-in Price List for specific amounts.
Q. Can I purchase the rubber feet for the LS-50C?
Applicable models: LS-50C, LS-50C-L II
A. We have replacement foot rubber (part number XA01). Please check Accessories & Spare Parts for prices and purchase methods.
Q. What is the difference between the LS-5C-XL and LS-65C?
Applicable models: LS-5C-XL, LS-65C
A. The LS-5C-XL features telescopic legs, includes aluminum hooks, and has a maximum load capacity of 3 kg. It uses the same 28 mm maximum diameter pole as the LS-65C. For details, please see the LS-5C-XL Product Information.
Note that the LS-65C has been superseded by the LS-6C-Pro. Please also see the LS-6C-Pro Product Information.
Note that the LS-65C has been superseded by the LS-6C-Pro. Please also see the LS-6C-Pro Product Information.
Q. What should I do if the LS-50C screws come loose? Are there torque specifications?
Applicable models: LS-50C, LS-50C-L
A. There are no specific torque settings. Using a thread-locking agent is effective. Note that the LS-50C-L has a rivet structure and does not have the corresponding screws.
If the threaded part is damaged, we accept repairs. Please see Support & Repairs.
If the threaded part is damaged, we accept repairs. Please see Support & Repairs.
Q. Can I attach the RH-100C-R II reflector holder to the LS-20C?
Applicable models: LS-20C, RH-100C-R II
A. You will need a separate 1/4" to 16mm male spigot adapter. We do not recommend using the LS-20C with large reflectors, as its small size makes it prone to tipping over.
Q. Is it okay to put a weight on the legs when the light stand is about to tip over?
A. Using a bag to hold down the legs is effective. Please avoid using metal weights, as they can damage the legs and are dangerous if the stand tips over. Also, do not step on the legs as this will cause damage.
Q. What should I do if the light stand pole gets stuck and doesn't move smoothly when extending?
A. Please fully loosen the locking nut (fixing knob) before extending or retracting the pole. This is often caused by sand or dust, so please clean the area around the pole and nut with a dry cloth.
If the issue persists, please contact us and we will provide guidance on replacing consumable parts.
If the issue persists, please contact us and we will provide guidance on replacing consumable parts.
Q. How do I attach the FT-01 Free Tilter to the LS-5C-XL / LS-50C-L II?
Applicable models: LS-5C-XL, LS-50C-L II, FT-01
A. Please use the included screw conversion adapter (1/4" male to 3/8" female). When attaching it to the FT-01, install it with the adapter's slit side facing downward.
Q. Is it a defect if the legs of a new LS-50C-L II are stiff and hard to open?
Applicable models: LS-50C-L II
A. The leg movement is designed to be stiff when new, which is within specifications. They will gradually loosen up with use.
If you suspect an abnormality, such as them not opening at all or having wobbling, please contact us with the details. After confirmation, we will provide guidance on exchanges or other necessary steps.
If you suspect an abnormality, such as them not opening at all or having wobbling, please contact us with the details. After confirmation, we will provide guidance on exchanges or other necessary steps.
Q. Can I use the LS-50C-L with an FT-01 Free Tilter or an umbrella attached?
Applicable models: LS-50C-L, FT-01
A. Yes, you can attach them. However, since the center of gravity will be higher and more prone to tipping, please ensure you do not exceed the load capacity (up to 1.5kg). Please ensure stability during use by fully extending the legs and using weights on the legs.