Cameras and combinations not listed here have not been tested. Please note that we are unable to answer any questions regarding the operation of these cameras.
When pairing with Air10s/MG80 Pro (commander mode) please also check the compatibility chart for Air10s/MG80 Pro.
FP/HSS (High Speed Synchro) flash is supported only in combination with a camera equipped with this function.
AF-assist lamp is not supported on Mirrorless cameras.
For Canon
The following camera names are listed by their Japanese names.
If you have a product for North America, Europe, or Asia, please use this link to look up the Japanese name.
EOS R10 / R6*1 / R5*1 / RP / R
EOS-1D X Mark II / 1D X / 1D Mark IV / 1D Mark III
EOS 7D Mark II / 7D / 6D Mark II / 6D / 5D Mark IV / 5Ds / 5DsR / 5D Mark III / 5D Mark II
EOS 90D / 80D / 70D / 60D / 50D / 40D
EOS 9000D / 8000D
EOS Kiss X10i*1 / EOS Kiss X10*1 / Kiss X9i*1 / Kiss X9*1 / Kiss X8i / Kiss X7i / Kiss X7 / Kiss X6i / Kiss X5 / Kiss X4 / Kiss X3 / Kiss X2
EOS Kiss X90 / Kiss X70 / Kiss X50 / Kiss F
EOS M6*2 / M5*2 / M3*2 / M*2
EOS Kiss M*2
The following cameras are compatible with Commander’s M mode (including Manual-HSS) and auto-zoom functionality, but tend to underexpose in TTL mode and cannot compensate for light modulation (compensation by the camera is also not possible). EOS R3 / R6 Mark II
The following cameras are not compatible with this product. PowerShot series
*1 Underexposure may occur by 0.5 to 1EV in TTL mode. *2 Wireless TTL by camera’s built-in flash is not usable for EOS M series. A separate optical transmitter such as Canon ST-E2 is required.
Remark: If you want to control it from Air1 for Sony, you need to update Air1 to Ver.2 or later firmware.
The following cameras are not compatible with this product. D2Hs / D2H / D100 / D1 / COOLPIX series other than the above / FinePix S3 Pro
*1 When this speedlight is used in on-camera mode, the flash may not fire normally in the release mode H+ (Continuous H (extended)). *2 Tends to underexpose when using auto FP flash. *3 To use with Z fc, please update the camera firmware version to 1.20 or higher. *4 The SD (Slave Digital) mode of this unit cannot be used.
Remark: 1. The Z series camera is supported by the firmware Ver. 9-7 of this unit. 2. If you want to control it from Air1 for Sony, you need to update Air1 to Ver.2 or later firmware.
For Sony
α1 / 7 / 7 II / 7 III / 7 IV / 7s / 7s II / 7s III*1 / 7R / 7R II / 7R III / 7R IV / 7R V / 7C / 9 / 9 II
α3000 / 6000 / 6300 / 6400 / 6500 / 6600
α58 / 77 II / 99 / 99 II
ZV-1*2 NEX-6
Cyber-shot RX1 / 1R / 1RM2*3 / 10 / 10M3 / 10M4 / 100M2
Cyber-shot HX60V / HX400V
*1 There is a tendency for overexposure during high-speed synchro flashes. *2 Since it uses a lens shutter, it can synchronize up to a shutter speed of 1/2000 second without switching.
*3 Slight interference (contact) with the EVF. Since diopter correction is not effective due to the interference, the EVF cannot be used.
Remark: 1. The light compensation function of the camera may not work properly with some cameras. The strobe’s light compensation function works properly.
2. Depending on the camera specifications, the continuous shooting speed may drop to the same level as that in low-speed continuous mode even when the camera is set to high-speed continuous mode.
3. Some Cyber-shot series cameras cannot use the continuous shooting function when an external speedlight is attached, depending on the camera’s specifications and firmware version. Please contact your camera manufacturer to check if your camera can use the continuous shooting function when an external speedlight is attached.
*1 When [S-OVF] is set to [On] and shooting with the EVF, the camera may become unstable. *2 If the unit is an older production lot, it may not emit light or it may be difficult to emit light. Please contact us if you experience any of these symptoms.
Remark: 1. When in optical wireless flash mode, the current (Micro Four Thirds generation) “Olympus wireless RC flash system” will be compatible. 2. Not compatible with older generation (E-series systems) wireless flash systems
*3 Tends to underexpose when firing FP in TTL mode. *4 The dimensions of the hot shoe are different from other models, so it may be tight and difficult to install. If this is the case, cleaning the hot shoe and the mounting feet may help. *5 The FP flash (HSS) of this Speedlight does not function properly because it is not officially supported by the camera.
Remark: Even though some Lumix series cameras can use a strobe during continuous shooting, depending on the specifications of the camera or the firmware version, the continuous shooting function may not work if an external strobe that is not guaranteed by the camera manufacturer is attached.
